GenII MP320 REM 240V Product Details - Innotech Control Systems

Home > Products > Product Search > Product Details > GenII MP320 REM 240V

GenII MP320 REM 240V

Digital / Remote Expansion Modules

This product has been discontinued.

Do you need help finding a replacement product? Contact Us
Email: sales@innotech.com
Phone: +61 7 3421 9100

The Innotech GenII MP REM Multipoint Module is a remote expansion device for the Genesis range of Digital Controllers.

The GenII MP REM is designed to be remotely located from the Genesis Digital Controller and provides 16A relay outputs and 0-10V analogue outputs for distributed control, digital inputs for status detection and a thermistor input for temperature measurement.

The GenII MP REM communicates with the Genesis Digital Controller via the GenII RMI Remote Module Interface that connects to the Local Expansion Module port of the Genesis. Local Expansion Modules cannot be connected to a Genesis Digital Controller that has a GenII RMI connected to it.

The GenII MP REM provides the Genesis Digital Controller with an RS485 link running at 38.4kbaud that communicates with all REM Modules.

(Larger image)

Download Datasheet Contact Us

FeaturesApplicationsApprovals & ListingsTech SpecsDownloadsHow To Buy

Remote sensing and control of I/O points up to 500 mtrs from the Genesis Controller via a single 10kΩ thermistor temperature sensor, four switched contact digital inputs and five outputs consisting of either:
- 5 x Relay Outputs (MP050)
- 4 x Relay Outputs & 1 x Analog Output (MP140)
- 3 x Relay Outputs & 2 x Analog Outputs (MP230)
- 2 x Relay Outputs & 3 x Analog Outputs (MP320)
RS485 interconnection between REM Modules.
240V AC operation.
JUMPER selectable Address Number (1-8).
Wiring Diagrams for modules generated by Gen2Config Software.
LED indication of Comms activity to assist in network setup and debugging.

Remote control of Fan Coil units using relay outputs for fan speed, compressor, reversing valve or electric heat; analogue outputs for VAV, economy cycle or chilled/hot water valves, with a thermistor measuring air temperature and DI’s used for pressure and HPT monitoring.

Application Notes
A Genesis Controller must have version 4 (or higher) firmware installed to support REM Modules. Version 4 (or higher) Config Software must be used to configure a Genesis Digital Controller that has standard MP050 Modules connected. MP REM Modules with Analogue Outputs (MP140, MP230 & MP320) require Version 5.00D (or higher) Config Software. A Genesis Digital Controller can have up to 8 GenII MP REM Modules* connected to it via the REM comms bus.

*One Genesis Digital Controller can have up to 15 GenII REM Modules attached to it. However, each REM Module has a “Resource Count” value that represents its requirement for Genesis Digital Controller resources. A Genesis Digital Controller supports a total resource count of 36.

The following shows the Resource Count for each of the currently available REM Modules:

Remote Module	Description	Resource Count
GenII MP050 REM	Multipoint Module	3
GenII MP140 REM	Multipoint Module	4
GenII MP230 REM	Multipoint Module	5
GenII MP320 REM	Multipoint Module	6
GenII AI REM	Analogue Input Module	6
GenII AO REM	Analogue Output Module	5
GenII DO REM	Digital Output Module	1
GenII DI REM	Dry Contact Digital Input Module	1
GenII IDI REM	Opto Isolated Digital Input Module	1
GenII PI REM	Pulse Input Module	5
GenII CS REM	Control Station Module	4
GenII CSAH REM	Control Station After Hours Module	4
GenII CSFCAH REM	Control Station With 3 Sp Fan	4
GenII MZS REM	Multi Zone Station Module	5
GenII MZSAH REM	Multi Zone After Hours Station Module	5

	CE	https://europa.eu/youreurope/business/product/ce-mark/index_en.htm The CE label is a European marking for products to indicate conformity with the electromagnetic compatibility and health and safety requirements set out in European Union.
	C-Tick	https://www.acma.gov.au The C-Tick compliance mark indicates that a device complies with applicable radiocommunications standards.

Power Supply

1 x Voltage: 240 volts AC ±10% @ 50/60Hz.
Power Consumption: 7VA max.

Inputs

10kΩ thermistor temperature sensor.
4 x Isolated switched contact digital inputs.

Outputs
MP050:

5 x 16A, 240V relays, Normally Open contacts.

MP140:

4 x 16A, 24V relays, Normally Open contacts.
1 x Analogue Output, 0-10VDC ± 0.05V into >2kΩ load.

MP230:

3 x 16A, 24V relays, Normally Open contacts.
2 x Analogue Outputs, 0-10VDC ± 0.05V into >2kΩ load.

MP320:

2 x 16A, 24V relays, Normally Open contacts.
3 x Analogue Outputs, 0-10VDC ± 0.05V into >2kΩ load.

Terminal Identification

240V = 240V AC Supply.
N = Neutral.
E = Earth.

Comms Connection

SHLD 1	=	Shield 1 from incoming Comms Cable.
C+	=	RS 485 (+) signal.
C-	=	RS 485 (-) signal.
SHLD 2	=	Shield 2 from outgoing Comms Cable.

Enclosure
The GENII MP REM Modules are housed in a rectangular case made from flame resistant Astrene M650 IR plastic in accordance with IEC695-2-1 (HD444-2-1) as of EN6335-1, A2 and IEC707 (AS/NZS2420).

Colour: Grey.
Mounting: DIN Rail mounted.
Dimensions: 107mm X 89mm X 69mm

I/O Terminal Connections

DI#n+	=	Digital Input positive.
DI#n-	=	Digital Input negative.
TH1	=	Temperature Sensor input.
TH2	=	Temperature Sensor input.
AO#n+	=	Analogue Output positive.
AO#n-	=	Analogue Output negative.
+12V	=	AUX DC Power for Digital Inputs.
Gnd	=	AUX DC Power for Digital Inputs.
NO	=	Normally Open relay contact.
Com	=	Common relay contact.